How to Use a Sewing Machine: Basic Steps Before Starting Your First Project!

Oct 06, 2020 06:30 PM

Photo by Mystic Art Design from Pixabay
SHARE

Tripboba.com - When you get a new sewing machine, you must be really excited to use it! But, you will get one big question about how to use a sewing machine.

Well, you don’t need to worry. You are not alone. And using a sewing machine is not that hard.

In this page, we will guide you with an easy tutorial with the basics of how to use a sewing machine. Enjoy!

How to use a brother sewing machine

Photo by dtenorioferreira1 from Pixabay

Now, we are going to learn how to use a sewing machine—brother sewing machine. You need to set-up your machine, figure out how to thread a bobbin.

After that, thread both the top and bottom cotton, so you are prepared to sew. Then, you need to figure out how to set the machine for straight sewing and should rehearse that for some time before you begin trying different things with different fastens.

Keep in mind that safety is the thing that should be considered consistently and whenever you are working around the needle and bobbin, making modifications, you ought to consistently switch off the power.

How to use a sewing machine for beginners

Photo by Willfried Wende from Pixabay

Now, we are going to learn about how to use a sewing machine in general. Look at these steps of how to use a sewing machine and let’s sew!

Step 1. Choose a straight stitch as well as a medium stitch length

Look at your manual for how to use a sewing machine. In some machines, stitches are set by rotating the lower handle on the right side of the machine until it fits properly. Continuously set the join with the needle up and out of the texture, since it might move the needle.

Step 2. Practice on some scrap material

The second step of how to use a sewing machine is to practice on some piece material. Pick a simple, woven material, not a weave one, for your first sewing experience.

Try not to utilize a heavy texture for your first trying at machine sewing. Denim and wool can be difficult to sew since they are too thick when a few layers are heaped together.

Step 3. Line up the texture under the needle

The third step of how to use a sewing machine is to line up the texture under the needle. Sew with the bulk of the material to the left side of the machine. In this step, crowding the bulk on the right side is able to cause bad sewing.

Step 4. Lower the presser foot onto the material

There is a switch behind or to the side of the needle gathering that raises or brings down the presser foot.

Step 5. Hold the loose ends of the two strings

For the initial few stitches, you'll have to hold these ends to keep them from retreating into the material. After you've sewed for a short distance, you can let go and utilize two hands to control the material and the machine.

Step 6. Press the foot pedal

The foot pedal is basically your speed control. Much the same as the gas pedal in a car, the harder you push it, the quicker you will go. Push it gradually from the outset, just enough to get the machine going.

Step 7. Discover the reverse button or lever and attempt it.

It turns around the direction that the machine feeds, hence, the material goes toward you as the machine sews. Frequently, this lever or button is spring-loaded, so you should hold it down to sew backward.

Step 8. Utilize the hand wheel to move the needle to its highest position

Then, raise the presser foot. The material has to pull out without any problem. If the sewing pulls back when you attempt to get rid of the material, you need to check the needle position.

Step 9. Cut the thread

On many machines, there is a little notch behind the post that holds the presser foot in place. You are able to hold both ends of the thread. After that, draw it down across this notch in order to cut the thread. In case you do not have such a notch, you can use scissors to cut the thread.

Step 10. Practice sewing a seam

Now, you can try working on sewing a seam. Pin two fabric pieces, right sides together, close to the edge. The seam will go 1/2 inch (1.3cm) to 5/8 inch (1.5cm) from the edge. You are able to sew a single layer of material.

But, since the objective of most machine sewing is to join two fabric pieces, you ought to become accustomed to sewing with two or three layers and pins.

Step 11. Move to another part of the material

Utilize the hand wheel at the head of the right side of the machine to move the needle to the head of its movement before beginning a seam and again to get rid of the material from the machine toward the end of a seam. This lifts the needle, and permits you to move to another part of the material you're working on.

Step 12. Figure out how to sew a sharp corner

Where you need to go, bring down the needle right into the material. You can utilize the hand wheel to bring down the needle. Raise the presser foot. Leave the needle down, in the material.

Then, rotate the material to the new position, leaving the needle in it. At last, bring down the presser foot with the material in the new position and resume sewing.

Step 13. Attempt a simple project

When you have made a variety of test seams and begin to feel good with the basic steps, have a go at sewing a pillowcase, pillow, cloth or gift bag.

Recommended

  1. 50 Birthday Wishes for Son in Law to Make Him Feel Special on the Special Day
  2. 66 Wedding Anniversary Wishes for Parents to Commemorate Their Love Journey
  3. 60 Valentine Wishes to Share the Joy of Love to Friends, Partner, and Children
  4. 13 Daily Struggles Comics Some People Will Relate To, Which One Are You?
  5. 50+ Inspirational Togetherness Quotes That Will Motivate You to Collaborate with Others!

TAGS